请说明根本原因如何不影响其他过程?哪位大神帮忙回答一下?
需求
9.1.1 General总则 The organization shall determine: 组织应确定: a) what needs to be monitored and measured; 需要监视和测量什么; b) the methods for monitoring, measurement, analysis and evaluation needed to ensure valid results; 需要用什么方法进行监视、测量、分析和评价,以确保结果有效;
不符合声明
The management of special characteristic is not fully effective. 特殊特性的管理不是完全有效的。
客观证据
Synchronizer number K2446 (G6013002), the width of 59 (-0.2, 0) and 75 (-0.3, 0) in the list of special characteristics, the parallelism 0.2 is recognized as a special characteristic, the sampling frequency is 5 pieces every 4 hours in the CP, and the common characteristic There is no difference in control methods. 编号K2446(G6013002)同步器,特殊特性清单中宽度59(-0.2,0)和75(-0.3,0),平行度0.2识别为特殊特性,控制计划中要求的抽样频次为每4小时5件,与普通特性的控制方法无差异。
分类理由
check the Y2020 CPK analysis result, the CPK of these 3 dimensions all over 1.67. this year totally produced 8106 pcs of this kind. no IPQC and OQC NCs, and also no complaints from customer side. low risk. 查看Y2020 CPK分析结果,这3个维度的CPK均超过1.67。 今年共生产此类产品8106台。 没有IPQC和OQC不符合,也没有客户投诉。 低风险。
纠正(遏制)措施,包括时间安排和负责人:
对特殊特性 宽度59(-0.2,0)和75(-0.3,0),平行度0.2进行加严控制,每6个月进行一次SPC分析, 11月20日落实到位,周建辉
实施的证据
更改《控制计划》中对这三个特殊特性的控制方法为 每隔6个月进行一次SPC分析
实施证据文件
2021年11月20日更新完成 《控制计划》
根本原因分析
1、相关人员仅仅按照自己以往的经验将《控制计划》中对特殊特性参数检测频率重新定义为4小时5件,但没有重新制作过程能力分析; 2、因为相关人员只是每年根据审核要求对特殊特性做一次过程能力分析,但不知道过程能力分析的控制频次和方法; 3、因为《统计技术及数据分析控制程序》中对于特殊特性没有规定进行过程能力分析的控制频次和方法;
请说明根本原因如何不影响其他过程?
需求
9.1.1 General总则 The organization shall determine: 组织应确定: a) what needs to be monitored and measured; 需要监视和测量什么; b) the methods for monitoring, measurement, analysis and evaluation needed to ensure valid results; 需要用什么方法进行监视、测量、分析和评价,以确保结果有效;
不符合声明
The management of special characteristic is not fully effective. 特殊特性的管理不是完全有效的。
客观证据
Synchronizer number K2446 (G6013002), the width of 59 (-0.2, 0) and 75 (-0.3, 0) in the list of special characteristics, the parallelism 0.2 is recognized as a special characteristic, the sampling frequency is 5 pieces every 4 hours in the CP, and the common characteristic There is no difference in control methods. 编号K2446(G6013002)同步器,特殊特性清单中宽度59(-0.2,0)和75(-0.3,0),平行度0.2识别为特殊特性,控制计划中要求的抽样频次为每4小时5件,与普通特性的控制方法无差异。
分类理由
check the Y2020 CPK analysis result, the CPK of these 3 dimensions all over 1.67. this year totally produced 8106 pcs of this kind. no IPQC and OQC NCs, and also no complaints from customer side. low risk. 查看Y2020 CPK分析结果,这3个维度的CPK均超过1.67。 今年共生产此类产品8106台。 没有IPQC和OQC不符合,也没有客户投诉。 低风险。
纠正(遏制)措施,包括时间安排和负责人:
对特殊特性 宽度59(-0.2,0)和75(-0.3,0),平行度0.2进行加严控制,每6个月进行一次SPC分析, 11月20日落实到位,周建辉
实施的证据
更改《控制计划》中对这三个特殊特性的控制方法为 每隔6个月进行一次SPC分析
实施证据文件
2021年11月20日更新完成 《控制计划》
根本原因分析
1、相关人员仅仅按照自己以往的经验将《控制计划》中对特殊特性参数检测频率重新定义为4小时5件,但没有重新制作过程能力分析; 2、因为相关人员只是每年根据审核要求对特殊特性做一次过程能力分析,但不知道过程能力分析的控制频次和方法; 3、因为《统计技术及数据分析控制程序》中对于特殊特性没有规定进行过程能力分析的控制频次和方法;
请说明根本原因如何不影响其他过程?